Loba 2K Invisible Protect A.T.

• For professional use only!
• BEFORE USING, READ AND UNDERSTAND ALL LABEL INSTRUCTIONS AND MATERIAL SAFETY DATA SHEETS.
• For technical advice call our Loba-Wakol Technical Service at 1-800.230.6456.
• Recommended conditions are 55°F-80°F/40-75%rH.
• Sand and prepare floors according to NWFA guidelines.
• WARNING! If you scrape, sand, or remove old paint from wood floors, you may release lead dust. Follow local and/or federal requirements for lead removal. Before you start, find out how to protect yourself and others by contacting the National Lead Information Hotline at 1-800-424-LEAD or log on to www.epa.gov/lead.
• ALWAYS PREPARE A SAMPLE OR TEST AREA TO DETERMINE COMPATIBILITY, APPEARANCE, AND DESIRED RESULTS.
• POT LIFE: 2 hours. For mixing the full container shake base well, and add complete hardener to base, replace lid, and then shake vigorously to mix. For mixing smaller quantities, mix at a ratio of 10 parts base : 1 part hardener. Use the LOBA Mixing Container or a scale to weigh out the components.
• Do not thin. Do not add water.
• Do not apply at temperatures below 55°F (13°C). Make sure material is at room temperature. Always maintain adequate ventilation during all phases of the coating and drying process.
• Apply evenly at the recommended coverage rate. Avoid streaks, puddles, and lap marks.
• This product is part of the LOBA and Wakol “Connected Systems”. The approved combinations with Wakol wood flooring adhesives may be found in the "Connected Systems Matrix": https://www.loba.de/us/connected-systems/

Application Tool

LOBA Roller Deluxe 120 - as a two coat system.
LOBA Roller Microfiber 100-120 - as a three coat system ONLY.
NOTE: Alternate applicators could apply less finish and will have an increased risk of application marks and are not recommended

Coverage

LOBA Roller Deluxe 120: apply at 325-375 square feet per gallon per coat.
LOBA Roller Microfiber 100/120: apply at 400-500 square feet per gallon per coat.

Drying time

• Earliest possilbe recoating after 4-6 hours.
• Fully cured after 5 days.

Recommended procedure for 2 coat application:

• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 4-6 hours minimum.
• Intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent) to remove grain raise.
• Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• NOTE: An optional third coat can be applied using the LOBA Roller Deluxe 120 and the procedures listed below for a 3 coat application can be followed.

Recommended procedure for 3 coat application using the LOBA Microfiber 100-120 roller:

• Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.
• Allow to dry for 2-4 hours minimum.
• Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.
• Allow to dry overnight.
• Intermediate sanding with LOBASAND 180 grit perforated pad (or equivalent) to remove grain raise.
• Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust. Apply 2K InvisibleProtect using the LOBA Roller Microfiber 100-120.

Alternative procedure to create natural oiled color:

• Prime with 2K Intensive Transparent refer to the Technical Data Sheet for details.
• Allow to dry for 16 hours minimum.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.
• Allow to dry for 2-4 hours minimum.
• Note: If intermediate sanding is required allow first coat to dry overnight.
• Apply 2K InvisibleProtect using the LOBA Roller Deluxe 120.

Suitable sealers:

A sealer is not required, however, 2K Invisible Protect can be applied over all LOBA sealers, finishes, and LOBA Stain.

Screen and Recoat

• Clean floor, abrade with LOBASAND 180 grit perforated pad (or equivalent). Vacuum floor then tack using a LOBA Mop and a new/clean LOBA microfiber mop pad lightly dampened with water to remove all dust.
• Apply finish following instructions.
• Always prepare test areas to determine compatibility, appearance, and desired results.

• Do NOT use on floors finished with UV cured, oxide containing, factory applied finishes.

For professional use only!